FlowBench / DHW Recirculation & Heat Loss

Domestic Hot Water Recirculation Loop & Heat Loss

Compute radial heat loss for insulated or bare DHW supply and return piping, solve required recirculation flow rate for your target ΔT drop, and calculate circulator TDH and return-line erosion velocity.

Radial Insulation Heat Loss Recirc GPM / L/s for ΔT ASHRAE 90.1 / ASPE Copper Erosion Check
DHW Recirculation & Thermal Loss Workbench Supply + Return Loop

Supply, Return & Insulation Inputs Return: 130 °F

ft
ft
in
°F
°F
°F
%

Recirculation Flow, Heat Loss & TDH Safe Velocity

Required Recirculation Flow Rate Return Vel: 0.78 ft/s
1.22 GPM
Total Loop Heat Loss 12.0 BTU/(hr·ft) avg
6,010 BTU/hr
Circulator Head Loss (TDH) 0.42 psi
0.98 ft H₂O
Supply Line Loss Rate
14.2 BTU/(hr·ft)
Return Line Loss Rate
9.8 BTU/(hr·ft)
Domestic hot water recirculation loop from water heater through insulated supply and return piping to circulator
Recirculation Loop Diagnostics

Calculating DHW loop heat loss and circulator duty...

Worked Equations & Live Substitution

Cylindrical Pipe Radial Heat Loss
q' = (T_water − T_amb) / [ ln(r₂/r₁)/(2πk) + 1/(2πr₂h_air) ]
Live: ...

Accounts for cylindrical insulation thickness (r₂ = r₁ + t_ins) and natural-convection outer surface film.

Recirculation Flow Rate & Loop TDH
Q_recirc = (q'_s·L_s + q'_r·L_r) / (ρ·cₚ·ΔT_allow)
Live: ...

Pump head combines Darcy-Weisbach friction along both supply and return legs plus fittings and check valve allowance.

ASHRAE 90.1 & IPC/ASPE DHW Recirculation Guidance

Energy Code Insulation & Temperature Safety

  • ASHRAE 90.1 / IECC: Commercial DHW recirculation piping requires at least 1.0 in (25 mm) insulation for pipes < 1-1/2" and 1.5 in for larger mains.
  • Legionella Mitigation: Store DHW at ≥ 140°F (60°C), maintain return temperature ≥ 124°F (51°C), and use ASSE 1017 master mixing valves at point of distribution.

Pump Selection & Balancing Valves

  • Stainless / Bronze Wetted Parts: Never use cast-iron hydronic circulators on open oxygenated DHW loops; specify bronze or stainless-steel circulators.
  • Multi-Riser Balancing: On multi-branch buildings, install thermostatic or calibrated balancing valves on each return riser so short loops do not starve distant risers.

Frequently Asked Questions

What allowable ΔT temperature drop is recommended for DHW recirculation loops?

ASHRAE and ASPE recommend sizing DHW recirculation flow for a 5°F to 10°F (3°C to 5.5°C) loop temperature drop so fixture wait times remain minimal and return water stays safely above Legionella proliferation temperatures (≥ 124°F / 51°C).

Why must copper DHW recirculation return velocities stay below 4 ft/s?

Continuous 24/7 circulation in hot, oxygenated domestic water accelerates erosion-corrosion (pitting) in copper tubing. Keeping return line velocity between 1.5 and 3.5 ft/s (0.45 to 1.1 m/s)—and never exceeding 4 to 5 ft/s—protects pipe walls and prevents noise.

How much does pipe insulation reduce recirculation pump size and energy loss?

Adding 1 inch (25 mm) of fiberglass or elastomeric foam insulation cuts radial pipe heat loss by 75% to 85% compared to bare copper, directly reducing the required recirculation flow rate, pump head loss, and annual water-heater standby fuel use.

Should the recirculation supply pipe heat loss be included when sizing the loop pump?

Yes. During zero-draw periods (overnight), both the supply main and the return line lose heat to the building spaces and carry the recirculation flow back to the water heater, so pump flow and TDH must account for the full supply + return circuit.