FlowBench / Expansion Tank Sizing

Closed-Loop Hydronic Expansion Tank Sizing

Calculate minimum diaphragm or bladder expansion tank volume per ASME BPVC Section IV, including pipe/boiler volume estimation, glycol thermal expansion, and tank acceptance factor.

ASME Section IV Formula Pipe + Boiler Estimator Water & Glycol Expansion ASHRAE Ch. 13
ASME Expansion Tank Workbench Diaphragm / Bladder

System Volume & Pressures Vs: 150 gal

gal
°F
°F
psi
psi
% vol

Tank Volume & Acceptance Factor Rec: ASME 21 gal

Minimum Required Tank Volume (Vₜ) Pre-charge: 12.0 psi
14.2 gal
Acceptance Factor (Fₐ)P_max: 27.0 psi
0.360
Expanded Fluid Volume3.41% net
5.11 gal
Fluid Thermal Expansion
3.73%
Piping Expansion Credit
0.32%
Diaphragm expansion tank cross-section showing expanded fluid volume vs. compressed nitrogen pre-charge cushion
Sizing & Commissioning Notes

Calculating expansion tank volume...

Worked Equations & Live Substitution (ASME Sec. IV)

Minimum Tank Volume (ASME Diaphragm Formula)
Vₜ = Vₛ · [ (v₂/v₁ − 1) − 3α(T_max − T_min) ] / [ 1 − (P_f + P_atm)/(P_max + P_atm) ]
Live: ...

Numerator is net expanded fluid volume (Vₐ); denominator is tank acceptance factor (Fₐ).

Acceptance Factor (Boyle's Law Gas Compression)
Fₐ = 1 − (P_fill,abs / P_max,abs)
Live: ...

Pressures must be converted to absolute pressure (+14.7 psi or +101.3 kPa at sea level).

ASHRAE & ASME Expansion Tank Guidance

Pre-Charge & Fill Pressure Rules

  • Cold Fill Pressure: Set P_fill = building static height (ft × 0.433 psi/ft) + 4 psi (28 kPa) positive pressure at the highest vent (minimum 12 psi / 83 kPa for residential loops).
  • Pre-Charge Verification: Always measure and adjust air pre-charge with the tank isolated from system water pressure so pre-charge equals P_fill.

Point of No Pressure Change

  • Pump Suction Connection: Connect the expansion tank at the pump suction (pumping away from the tank) so pump head adds positively to system pressure rather than causing sub-atmospheric air suction or cavitation at high vents.
  • Glycol Allowance: Propylene and ethylene glycol expand significantly more than pure water; never size glycol loops using water-only charts.

Frequently Asked Questions

How should the air pre-charge pressure of a diaphragm expansion tank be set?

Before connecting or while isolated at zero water pressure, the expansion tank air/nitrogen pre-charge must be adjusted to match the system cold-fill gauge pressure (typically 12 psi for residential 1–2 story buildings, or static height + 4 psi for taller buildings).

Why does glycol require a larger hydronic expansion tank than pure water?

Ethylene and propylene glycol solutions have a 20% to 50% higher volumetric thermal expansion coefficient than pure water over the same temperature swing, increasing the expanded fluid acceptance volume and required tank size.

What is the ASME Section IV acceptance factor?

The acceptance factor Fₐ = 1 − (P_fill_abs / P_max_abs) represents the fraction of the tank's total volume available to absorb expanding fluid before system pressure reaches P_max. Dividing expanded fluid volume by Fₐ gives the minimum required tank volume.

Why apply a 10% safety margin below the relief valve setting?

ASME and ASHRAE recommend sizing P_max at 90% of the relief valve setting (e.g., 27 psig for a 30 psig relief valve) so pump pressure fluctuations, instrument tolerance, and thermal overshoot do not cause relief valve weeping.