FlowBench / Orifice Plate & Balancing Valve

Orifice Plate & Balancing Valve Flow Measurement

Convert measured differential pressure (ΔP) across a concentric orifice plate (ISO 5167 Reader-Harris/Gallagher β ratio) or a calibrated balancing valve (Cᵥ / Kᵥ) into volumetric flow rate and permanent unrecovered head loss.

ISO 5167 Orifice Plate Calibrated Valve Cᵥ / Kᵥ Permanent Head Loss TAB Commissioning
Flow Metering & TAB Balancing Workbench Orifice / Balancing Valve

Meter Geometry & Measured ΔP β = 0.544

in
psi
°F

Flow Rate & Permanent Head Loss β within ISO 5167

Measured Volumetric Flow Rate 8.55 m³/h | SG 1.00
37.7 GPM
Permanent Unrecovered Loss 69.1% of ΔP
2.42 psi
Permanent Head Loss Cd = 0.606
5.58 ft H₂O
Upstream Pipe Velocity
3.60 ft/s
Equivalent Meter Cᵥ
20.1
Differential pressure flow measurement across concentric orifice plate or calibrated balancing valve
TAB Measurement & Recovery Notes

Calculating flow rate and permanent loss...

Worked Equations & Live Substitution

Orifice / Balancing Flow Equation
Q = C_d · [Aₒ / √(1 − β⁴)] · √(2ΔP / ρ)  |  Q_GPM = Cᵥ · √(ΔP_psi / SG)
Live: ...

Flow scales with the square root of measured ΔP; 10x flow turndown produces 100x ΔP turndown.

Permanent Unrecovered Pressure Loss (ISO 5167)
Δϖ / ΔP = [ √(1 − β⁴(1−C_d²)) − C_dβ² ] / [ √(1 − β⁴(1−C_d²)) + C_dβ² ]
Live: ...

Must be added to loop TDH when sizing the main system pump so permanent meter drag is accounted for.

ISO 5167 & NEBB/TAB Field Measurement Guidance

Straight-Pipe Upstream & Downstream Runs

  • Orifice Plates: ISO 5167 requires 10D to 30D straight pipe upstream (depending on elbows/valves) and 5D downstream to eliminate swirl distortion.
  • Balancing Valves: Maintain at least 5D straight pipe upstream and 2D downstream of calibrated circuit setters per NEBB/AABC standards.

Manometer Accuracy & β Selection

  • Avoid Low ΔP Readings: Size orifice β (typically 0.45–0.65) or set balancing valve throttling so design ΔP falls between 1.0 and 5.0 psi (7–35 kPa)—high enough for accurate gauge reading without excessive pump energy waste.
  • Bleed Test Hoses: Always purge air from manometer hoses before zeroing and reading differential pressure.

Frequently Asked Questions

What is the β (beta) ratio of a concentric orifice plate and its valid ISO 5167 range?

The beta ratio β = d / D is the orifice bore diameter divided by the upstream pipe internal diameter. ISO 5167-2 specifies β between 0.20 and 0.75 (typically 0.40 to 0.65 in hydronic balancing) for predictable vena contracta discharge coefficients.

How much differential pressure is permanently lost across an orifice plate?

Unlike a Venturi meter that recovers 85% to 90% of measured ΔP, a sharp-edged concentric orifice plate loses roughly (1 − β¹.&sup9;) of the measured differential pressure permanently as turbulent eddies—typically 50% to 85% of ΔP.

How do TAB technicians compute flow from a calibrated balancing valve?

Testing, Adjusting, and Balancing (TAB) technicians measure ΔP across the valve's P/T test ports using a digital manometer, look up the valve's Cᵥ at its handwheel turn setting, and solve Q (GPM) = Cᵥ × √(ΔP_psi / SG).

Why must fluid specific gravity (SG) be included for glycol or hot water flow measurement?

Differential pressure meters respond to dynamic head ρV²/2. A 40% glycol mixture or 35°F chilled water has a higher specific gravity than 180°F hot water, shifting the actual volumetric flow rate for a given ΔP reading.